Quick Installation Guide EmCORE-v611
3.5" form factor Embedded VIAEden CPU Core Modulewith 128 MB SDRAM, CRT SVGA,Dual Fast Ethernet, AC97 3D Audio,PC/104 and Compact Flash Socket
Copyright 2002 All Rights Reserved.
The information in this document is subject to change without prior notice inorder to improve the reliability, design and function. It does not represent acommitment on the part of the manufacturer.
Under no circumstances will the manufacturer be liable for any direct,indirect, special, incidental, or consequen-tial damages arising from the use orinability to use the product or documentation, even if advised of the possibilityof such damages.
This document contains proprietary information protected by copyright. Allrights are reserved. No part of this manual may be reproduced by anymechanical, electronic, or other means in any form without prior writtenpermission of the manufacturer. 2 EmCORE-v611 Quick Installation
Single Board Computers and their components contain very delicateIntegrated Circuits (IC). To protect the Single Board Computer and itscomponents against damage from static electricity, you shouldalways follow the following precautions when handling it :
1. Disconnect your Single Board Computer from the power source when you
2. Hold the board by the edges and try not to touch the IC chips, leads or
3. Use a grounded wrist strap when handling computer components.
4. Place components on a grounded antistatic pad or on the bag that came
with the Single Board Computer, whenever components are separatedfrom the system
Replacing the lithium battery
Incorrect replacement of the lithium battery may lead to a risk of explosion.
The lithium battery must be replaced with an identical battery or a batterytype recommended by teh manufacturer (BR2335).
Do not throw lithium batteries into the trashcan. It must be disposed of inaccordance with local requlations concerning special waste. Technical Support
If you have any technical difficulites, please consult the user's manual firstat:
Please do not hesitate to call or e-mail our customer service when you stillcan not find out the answer. EmCORE-v611 Quick Installation 3 Specifications General Specifications
• CPU : VIA Ultra Low Power Embedded Eden 667MHz processor (400 ~800
MHz for option) with FSB 66/100/133 MHz EBGA package. Chipset : VIA VT8606 TwisterT with Integrated Savage4 AGP 4X Graphics core and VT82C686B Super "South Bridge" BIOS : AWARD® Flash BIOS Green Function : power saving supported in BIOS. DOZE / STANDBY / SUSPEND modes, ACPI & APM L1 Cache : Integrated on CPU (128KB) L2 Cache : Integrated on CPU (64 KB) DRAM Memory : Onboard 128 (256MB option) SDRAM, and up to 512MB of SDRAM on SODIMM (Total of 768MB Memory) Enhanced IDE with UltraDMA : supports 1 port and up to 2 ATAPI devices, Ultra DMA transfer 33 / 66 and 100 MB/sec. One 40-pin (2.54 pitch) box header. Watchdog Timer : 127-level timer generates RESET or NMI when your application loses control over the system. Real-time Clock : built-in chipset with lithium battery backup. CMOS data backup of BIOS setup and BIOS default. High Speed Multi I/O Chipset : VIA VT82C686B Serial Ports : One high speed RS-232C ports (COM1). One high speed RS-232C/422/485 port COM2 (jumper selectable). Both with 16C550 compatible UART and 16 byte FIFO. USB : Two onboard USB ver 1.1 ports SIR Interface : onboard IrDA TX/RX port Floppy Disk Drive Interface : 2 floppy disk drives, 3½ " (720 KB, 1.44 MB or 2.88 MB). Bi-directional Parallel Port : SPP, EPP and ECP mode. Keyboard and Mouse Connectors : external PS/2 KB/Mouse port (2-in- 1 mini DIN) onboard AT Keyboard port (5-pin box header) Audio Chipset: VIA VT82C686B, AC97 2.0 compliant, Multistream Direct Sound and Direct Sound 3D acceleration. (Line-in, CD Audio in, MIC in, Speaker out) 4 EmCORE-v611 Quick Installation Network Interface Controller Chipset : 2 x Realtek 8139C, 10/100 Mbps (EmCORE-v611VL2/R Series) Connector : Duak external RJ-45 with LEDs on bracket Display Controller Chipset : 4x AGP S3 Savage4 3D and S3 Savage 2000 2D engines integrated in VT8606 supports up to 32MB of Shared Memory Display Type : CRT (VGA, SVGA, XGA, SXGA) and LCD Type Connectors : external DB15 for CRT on bracket Resolution: Single Channel of LVDS / 36-bit of TTL and 12-bit of TMDS; all resolutions are supported up to 1280x1024. Flash Disk Compact Flash Card (CFC) - Compact Flash Socket : supports Type I/II CFC - Capacity : up to 512MB CFC Environmental and Power Power Requirements : +5 V @ 1.8 A (typical), +12 V @ 0.13A (typical) ;(Low Power Embedded 667MHz and 128MB SDRAM) System Monitoring and Alarm : CPU and System temperature, system voltage and cooling fan RPM. Board Dimensions : 145mm x 102mm Board Weight : 0.18kg Operating Temperature : 0 to 60° C (32 to 140° F) EmCORE-v611 Quick Installation 5 Packing list
Before you begin installing your single board, please make sure that thefollowing materials have been shipped:
> 1 x EmCORE-v611 3.5" Embedded VIA Eden SBC
> 1 x Cable Kits (CBK-09-0611-00) contains the followings:
Ordering Codes EmCORE-v611VL2R/E533
3.5" form factor Embedded VIA Eden 533MHzSingle Board Computer with 128MB SDRAM,CRT SVGA, Dual Fast Ethernet, AC97 3D Audio,PC/104 and Compact Flash Socket
EmCORE-v611VL2R/E667
3.5" form factor Embedded VIA Eden 667MHzSingle Board Computer with 128MB SDRAM,CRT SVGA, Dual Fast Ethernet, AC97 3D Audio,PC/104 and Compact Flash Socket
EmCORE-v611VL2R/E800
The same as above with VIA Eden 800MHz CPU(option)
6 EmCORE-v611 Quick Installation Board Layout Front Twister T VT82C686B EmCORE-v611 Quick Installation 7 Board Layout Front H AS ETCKCT FLOPAMD SRCOCA 8 EmCORE-v611 Quick Installation Jumper/Connector Quick Reference EmCORE-v611 Quick Installation 9 Jumper/Connector Quick Reference 10 EmCORE-v611 Quick Installation CMOS Jumper Settings CMOS Operation (J1)
If the EmCORE-v611 refuses to boot due to inappropriate CMOS settings hereis how to proceed to clear (reset) the CMOS to its default values. CMOS Setup (J1) Watchdog Timer Mode Setting (J2) Watchdog Mode EmCORE-v611 Quick Installation 11 Serial Port Selection (RS232C/422/485) RS-232/422/485 Mode select (J4) RS-422/485 Mode on COM2
The onboard COM2 port can be configured to operate in RS-422 or RS-485modes. RS-422 modes differ in the way RX/TX is being handled. Jumper J4switches between RS-232 or RS-422/485 mode. When J4 is set to RS-422 or485 mode, there will be only +12V output left while J4 is set. All of the RS-232/422/485 modes are available on COM2. COM2 Pin Defined: RS232 RS422 J4 Selection 1-2 3-4 5-6 12 EmCORE-v611 Quick Installation Voltage select LCD Voltage Select (JV9) LCD Voltage RS-232c Standard and POS Modes (JV1~JV4)
All onboard COM ports can be configured to operate in standard RS-232cmode or in POS (Point-of-Sale) RS-232c mode. POS devices normally need anadditional power supply signal (5V or 12V) to be able to power the device(LCD, cash drawer or printer) without additional wiring.
- RS-232 with 5V on pin 1 and 12V on pin 9
COM1 RS-232 Mode COM2 RS-232 Mode EmCORE-v611 Quick Installation 13 16-bit Digital I/O 16-bit General Purpose I/O (DIO1)
Connector : DIO1 Type : Onboard 20-pin header
Output Port I/O Address: 208hex and from Pin1 to Pin8Input Port I/O Address: 200hex and from Pin11 to Pin18
LANLED Connector
Connector: LANLEDType : 8-pin onboard Wafer connector
Description Description 14 EmCORE-v611 Quick Installation Power Connector ATX power control (ATX1) Type : 3-pin onboard Wafer connector Description Power Connector (PWR1)
Connector : PWR1 Type : 4 pin Description Description CPU Fan Connector
Connector : CPUF1 Type : onboard 3-pin wafer connector Description EmCORE-v611 Quick Installation 15 Switches and Indicators Power Switch Reset Switch SMI Switch POWER LED
Connector : FRT Type : onboard 20-pin header Description 16 EmCORE-v611 Quick Installation
Introduction Over the last 20 years, scholars have devoted considerable attention to the ability of farmers, fishermen, pastoralists and other types of resource users to organize, adopt, monitor and enforce institutional arrangements that govern their use of common pool resources (CPRs) in a sustainable manner (Ostrom et al ., 2002). During this period, progress has been made in carefully iden
THYROID ASSESSMENT Hair tissue mineral analysis offers excellent information about thyroid activity and often very different information than blood tests. The hair assessment can be extremely helpful, especially in a common syndrome that one might call secondary hyperthyroidism. Most confusion arises because blood thyroid tests do not reveal much about thyroid physiology. Standard tests only